PAROC Hvac Dots

PAROC Hvac Dots Acessory
PAROC Hvac Dots are the optimal solution when it comes to cover pins’ heads. This is fast, clean, generates a good looking, smooth, gapless and tight insulation surface. No risk of condensation. It is also very easy to lift the single dot from the release paper.

Datasheet

 
Updated 7 Apr 2021

Width
Dots diameter: 60 mm
Volume
Dots on a roll: 750 dots/roll
Packing: 8 rolls/box

Other Properties

Other Properties
PropertyValue
Adhesiveacrylic
. 
Release linersiliconized paper
. 
Temperature range-30 °C to 120 °C
. 
Storage conditions12 months inside warehouse in 21 °C and 50% air humidity, no direct sunlight.
. 
Installation temperature10 °C to 40 °C

Facings

Facing Material
Aluminum foil

Colours

Aluminum, bright

Installation

During the installation, the insulation material to be taped should be at a minimum temperature of 10 °C. Allow the temperature of the insulating material to adjust to the ambient installation temperature. Make sure that the surfaces to be joined with tape are clean, dry free of dust and grease. Surface must be free from oil, fat, dust and solvents before film/tape application. Do not use cleaners containing anti-adhesive agents. Some plastics and paints may discharge anti-adhesive agents leading to bonding failure. Rough and uneven surfaces may weaken bonding.

Handling and Storage

Product should be stored in original packaging, laid flat on the slit edge of the roll. Storage in dry and clean areas, at normal temperature, protected from direct sunlight and heat sources.

More Information

We strongly advise users to test the product ‘s suitability for their own particular requirement. All data and recommendations contained in this Technical Data Sheet are based on our own test.

Width
Dots diameter: 60 mm
Volume
Dots on a roll: 750 dots/roll
Packing: 8 rolls/box

Other Properties

Other Properties
PropertyValue
Adhesiveacrylic
. 
Release linersiliconized paper
. 
Temperature range-30 °C to 120 °C
. 
Storage conditions12 months inside warehouse in 21 °C and 50% air humidity, no direct sunlight.
. 
Installation temperature10 °C to 40 °C

Facings

Facing Material
Aluminum foil

Colours

Aluminum, bright

Installation

During the installation, the insulation material to be taped should be at a minimum temperature of 10 °C. Allow the temperature of the insulating material to adjust to the ambient installation temperature. Make sure that the surfaces to be joined with tape are clean, dry free of dust and grease. Surface must be free from oil, fat, dust and solvents before film/tape application. Do not use cleaners containing anti-adhesive agents. Some plastics and paints may discharge anti-adhesive agents leading to bonding failure. Rough and uneven surfaces may weaken bonding.

Handling and Storage

Product should be stored in original packaging, laid flat on the slit edge of the roll. Storage in dry and clean areas, at normal temperature, protected from direct sunlight and heat sources.

More Information

We strongly advise users to test the product ‘s suitability for their own particular requirement. All data and recommendations contained in this Technical Data Sheet are based on our own test.

Width
Dots diameter: 60 mm
Volume
Dots on a roll: 750 dots/roll
Packing: 8 rolls/box

Other Properties

Other Properties
PropertyValue
Adhesiveacrylic
. 
Release linersiliconized paper
. 
Temperature range-30 °C to 120 °C
. 
Storage conditions12 months inside warehouse in 21 °C and 50% air humidity, no direct sunlight.
. 
Installation temperature10 °C to 40 °C

Facings

Facing Material
Aluminum foil

Colours

Aluminum, bright

Installation

During the installation, the insulation material to be taped should be at a minimum temperature of 10 °C. Allow the temperature of the insulating material to adjust to the ambient installation temperature. Make sure that the surfaces to be joined with tape are clean, dry free of dust and grease. Surface must be free from oil, fat, dust and solvents before film/tape application. Do not use cleaners containing anti-adhesive agents. Some plastics and paints may discharge anti-adhesive agents leading to bonding failure. Rough and uneven surfaces may weaken bonding.

Handling and Storage

Product should be stored in original packaging, laid flat on the slit edge of the roll. Storage in dry and clean areas, at normal temperature, protected from direct sunlight and heat sources.

More Information

We strongly advise users to test the product ‘s suitability for their own particular requirement. All data and recommendations contained in this Technical Data Sheet are based on our own test.