PAROC Clad Dots

Paroc Clad Dots
PAROC Clad Dots are a clean, fast and convenient way to cover the pins' heads. Water resistant butyl rubber self-adhesive patches with very high tack and ageing resistance, come on a roll and can be attached directly on the head pins with the help of a spatula. This is fast and clean, generates a smooth, gapless and tight outdoor insulation surface. It is very easy to lift the single dot from the release paper.

Datasheet

 
Updated 23 Mar 2022

Usage Conditions
Temperature range: -30 °C to +80 °C.
Thickness
NPD
Diameter
90 mm

Packaging

Package Type
100 dots/roll, 6 rolls/box

Other Properties

Other Properties
PropertyValue
Backing:PET/Aluminum/PET-film composite
Release liner:Siliconized film
Adhesive:Butyl rubber
Tensile strength:NPD
Adhesion:NPD

Facings

Facing Material
PET/Aluminum/PET-film composite

Colours

Aluminum, bright

Installation

During the installation, the insulation material to be taped should be at a minimum temperature of +10 Celsius. Allow the temperature of the insulating material to adjust to the ambient installation temperature. Make sure that the surfaces to be joined with tape are clean, dry, free of dust and grease. Surface must be free from release agents, oil, fat, dust and solvents before tape application. Do not use cleaners containing anti-adhesive agents. Some plastics and paints may discharge anti-adhesive agents leading to bonding failure. Rough and uneven surfaces may weaken bonding.

Installation temperature: +10 °C ÷ +40 °C.

Handling and Storage

Product should be stored in original packaging, laid flat on the slit edge of the roll. Storage in dry and clean areas, at normal temperature, protected from direct sunlight and heat sources. Storage conditions: +10°C- +25°C, under dry conditions inside a warehouse.

More Information

We strongly advise users to test the product‘s suitability for their own particular requirement. All data and recommendations contained in this Technical Data Sheet are based on our own test results and practical experience and are aimed at helping customers select the appropriate tape for a given application. This information is provided without liability. We reserve the right to change the technical specification without prior notice.

Usage Conditions
Temperature range: -30 °C to +80 °C.
Thickness
NPD
Diameter
90 mm

Packaging

Package Type
100 dots/roll, 6 rolls/box

Other Properties

Other Properties
PropertyValue
Backing:PET/Aluminum/PET-film composite
Release liner:Siliconized film
Adhesive:Butyl rubber
Tensile strength:NPD
Adhesion:NPD

Facings

Facing Material
PET/Aluminum/PET-film composite

Colours

Aluminum, bright

Installation

During the installation, the insulation material to be taped should be at a minimum temperature of +10 Celsius. Allow the temperature of the insulating material to adjust to the ambient installation temperature. Make sure that the surfaces to be joined with tape are clean, dry, free of dust and grease. Surface must be free from release agents, oil, fat, dust and solvents before tape application. Do not use cleaners containing anti-adhesive agents. Some plastics and paints may discharge anti-adhesive agents leading to bonding failure. Rough and uneven surfaces may weaken bonding.

Installation temperature: +10 °C ÷ +40 °C.

Handling and Storage

Product should be stored in original packaging, laid flat on the slit edge of the roll. Storage in dry and clean areas, at normal temperature, protected from direct sunlight and heat sources. Storage conditions: +10°C- +25°C, under dry conditions inside a warehouse.

More Information

We strongly advise users to test the product‘s suitability for their own particular requirement. All data and recommendations contained in this Technical Data Sheet are based on our own test results and practical experience and are aimed at helping customers select the appropriate tape for a given application. This information is provided without liability. We reserve the right to change the technical specification without prior notice.

Usage Conditions
Temperature range: -30 °C to +80 °C.
Thickness
NPD
Diameter
90 mm

Packaging

Package Type
100 dots/roll, 6 rolls/box

Other Properties

Other Properties
PropertyValue
Backing:PET/Aluminum/PET-film composite
Release liner:Siliconized film
Adhesive:Butyl rubber
Tensile strength:NPD
Adhesion:NPD

Facings

Facing Material
PET/Aluminum/PET-film composite

Colours

Aluminum, bright

Installation

During the installation, the insulation material to be taped should be at a minimum temperature of +10 Celsius. Allow the temperature of the insulating material to adjust to the ambient installation temperature. Make sure that the surfaces to be joined with tape are clean, dry, free of dust and grease. Surface must be free from release agents, oil, fat, dust and solvents before tape application. Do not use cleaners containing anti-adhesive agents. Some plastics and paints may discharge anti-adhesive agents leading to bonding failure. Rough and uneven surfaces may weaken bonding.

Installation temperature: +10 °C ÷ +40 °C.

Handling and Storage

Product should be stored in original packaging, laid flat on the slit edge of the roll. Storage in dry and clean areas, at normal temperature, protected from direct sunlight and heat sources. Storage conditions: +10°C- +25°C, under dry conditions inside a warehouse.

More Information

We strongly advise users to test the product‘s suitability for their own particular requirement. All data and recommendations contained in this Technical Data Sheet are based on our own test results and practical experience and are aimed at helping customers select the appropriate tape for a given application. This information is provided without liability. We reserve the right to change the technical specification without prior notice.